What do they fit?

Get or give advice on equipment, reloading and other technical issues.

Moderator: Mod

Message
Author
Triplejim
Posts: 598
Joined: Mon Nov 14, 2005 12:48 pm

What do they fit?

#1 Postby Triplejim » Tue Feb 25, 2020 2:50 pm

The slot is offset, could be inside case deburrer.
If so, what brand tool do they fit?
You do not have the required permissions to view the files attached to this post.

pjifl
Posts: 883
Joined: Fri Jun 17, 2005 12:15 pm
Location: Innisfail, Far North QLD.

Re: What do they fit?

#2 Postby pjifl » Tue Feb 25, 2020 2:56 pm

I never thought they were intended to fit any tool but to be used hand held. They do work OK hand held both inside and outside but are not as good as the other fluted type deburrer.

DenisA
Posts: 1526
Joined: Wed Nov 09, 2011 7:00 pm
Location: Sunshine Coast, QLD

Re: What do they fit?

#3 Postby DenisA » Tue Feb 25, 2020 3:23 pm

I have one from when I started reloading. Pretty certain they are Lyman brand. They don't fit any tool. They are a chamfer and deburr tool used in your finger tips, hence the knurling. Only takes about 3 cases before your knuckles are locked up solid and you cant feel your finger tips anymore.

Rich4
Posts: 534
Joined: Sun Feb 24, 2019 2:33 pm
Location: Chinchilla

Re: What do they fit?

#4 Postby Rich4 » Tue Feb 25, 2020 3:33 pm

Lee chamfer/deburrer they do work somewhat, I have one, I also have a Wilson, I don’t use the Lee

stu_bear2002
Posts: 186
Joined: Fri Jun 16, 2006 10:01 pm
Location: Bribie Island QLD

Re: What do they fit?

#5 Postby stu_bear2002 » Tue Feb 25, 2020 3:37 pm

chamfer & deburing tool that come with every press kit made by Lee Precision.
heres an extra tip/use for them too.. they also work well to clean up a damaged thread on nuts and bolts if you"ve dropped them on concrete or similar \:D/ .
Stiller/holeshot .22LR
Bruno mod2(sleeved) .22LR
Rem7(sleeved) 6mmBR and 6mm Dasher
Stolle panda 6PPC
Winchester 101 12g

mike H
Posts: 623
Joined: Mon May 08, 2006 5:34 pm
Location: JUNEE NSW

Re: What do they fit?

#6 Postby mike H » Tue Feb 25, 2020 3:44 pm

As Rich4 said,Lee hand held chamfer tool.

AllanH
Posts: 22
Joined: Fri Sep 07, 2007 5:15 pm
Location: Sydney

Re: What do they fit?

#7 Postby AllanH » Tue Feb 25, 2020 3:44 pm

They work well in conjunction with the Lee case trim tool that provides a case holder that fits in a cordless drill. Trim the cases to length and then use the chamfer tool to quickly trim the inside and outside of the case mouth.

KHGS
Posts: 934
Joined: Thu Oct 20, 2005 12:46 am
Location: Cowra NSW

Re: What do they fit?

#8 Postby KHGS » Tue Feb 25, 2020 4:30 pm

Rich4 wrote:Lee chamfer/deburrer they do work somewhat, I have one, I also have a Wilson, I don’t use the Lee

You are correct, not one of Lee's better tools.
Keith H.

Triplejim
Posts: 598
Joined: Mon Nov 14, 2005 12:48 pm

What do they fit?

#9 Postby Triplejim » Wed Feb 26, 2020 8:32 am

Many tks for all the replies, I'Ii try them on some 1/4" UNF SHCS :-)

pjifl
Posts: 883
Joined: Fri Jun 17, 2005 12:15 pm
Location: Innisfail, Far North QLD.

Re: What do they fit?

#10 Postby pjifl » Wed Feb 26, 2020 10:31 am

One of my early acquisitions was a Hornady reloading 'kit' although I did have a good old Aussie press. I am fairly sure one of these came in the kit.

Peter Smith.


Return to “Equipment & Technical”

Who is online

Users browsing this forum: No registered users and 40 guests