Nightforce Benchrest 12-42 x 56 running out of elevation
Moderator: Mod
-
- Posts: 162
- Joined: Thu Feb 25, 2016 11:07 am
- Location: Qld
Re: Nightforce Benchrest 12-42 x 56 running out of elevation
Eg
You do not have the required permissions to view the files attached to this post.
-
- Posts: 424
- Joined: Sat Sep 16, 2017 5:39 pm
Re: Nightforce Benchrest 12-42 x 56 running out of elevation
Cutanything wrote:You need to move rail forward so back is flush with action you currently only have around 10 to 12 moa
It wont make any difference other than changing the height of the scope as the angle is between the top and bottom face of the rail.
If it were me I would 1st set the action level, then fit the rail and measure the angle, then add the bottom half of the scope rings, place a suitable sized piece of bar stock in the scope bases and measure again to find where the inaccuracy is coming from.
-
- Posts: 69
- Joined: Sun Feb 04, 2018 11:07 pm
Re: Nightforce Benchrest 12-42 x 56 running out of elevation
pay someone qualified to do it properly and start to enjoy shooting, rather than getting frustrated
-
- Posts: 15
- Joined: Sun Feb 25, 2018 2:03 pm
Re: Nightforce Benchrest 12-42 x 56 running out of elevation
johno wrote:pay someone qualified to do it properly and start to enjoy shooting, rather than getting frustrated
Yep.
Funny that you should say that. On Friday night I deccided to send it in to the gunsmith to sort out while he fits a new barrel.
When the gunsmith tells me what the issue is, I will post it here.
Thank you everyone for your replies and assistance.
-
- Posts: 69
- Joined: Sun Feb 04, 2018 11:07 pm
Re: Nightforce Benchrest 12-42 x 56 running out of elevation
looking at where your front ring was just wonder if head of screw was a little proud of rail
-
- Posts: 408
- Joined: Sat Feb 08, 2014 6:58 pm
- Location: Barossa Valley
-
- Posts: 15
- Joined: Sun Feb 25, 2018 2:03 pm
Re: Nightforce Benchrest 12-42 x 56 running out of elevation
johno wrote:looking at where your front ring was just wonder if head of screw was a little proud of rail
Hi Johno
I also thought so but a straight edge proved me wrong.
I finally managed to find time to drop it off with the gunsmith today. We shall see...
-
- Posts: 18
- Joined: Tue Jun 24, 2014 10:48 pm
- Location: Brisbane
Re: Nightforce Benchrest 12-42 x 56 running out of elevation
Frount of scope on rail . rings to close to geather
EWM
EWM
-
- Posts: 23
- Joined: Sun Dec 06, 2015 6:58 am
Re: Nightforce Benchrest 12-42 x 56 running out of elevation
Hey mate you need to push your rail forward,so it is flush with rear of action also check that you have got clearance,from front of scope bell too the barrel Marty
-
- Posts: 69
- Joined: Sun Feb 04, 2018 11:07 pm
-
- Posts: 15
- Joined: Sun Feb 25, 2018 2:03 pm
Re: Nightforce Benchrest 12-42 x 56 running out of elevation
EWM wrote:Frount of scope on rail . rings to close to geather
EWM
Hi EWM
Nope, just a badly angled photo. The objective bell is well clear of the rail. I am not sure how the rings being too close together can affect my useable elevation so badly though, especially in conjunction with a 20moa rail?
I have not heard from the gunsmith as yet, but he did say to only start calling after 2 weeks which is next week Tuesday.
-
- Posts: 1629
- Joined: Wed Aug 05, 2009 9:49 am
Re: Nightforce Benchrest 12-42 x 56 running out of elevation
Try moving the rail forward
id quod est
-
- Posts: 11
- Joined: Tue Feb 13, 2018 7:54 pm
Re: Nightforce Benchrest 12-42 x 56 running out of elevation
just looking at your pictures and noticed that your front scope rings are mounted directly over the area where your rail should be screwed down to your action. By any chance have you checked that the screw heads are flush with the bottom of the machined surface where the scope ring locator sits, or is it proud and the ring is sitting proud on the rail? Also looking at the rear of the rail on the action, dose not look to be mounted on the true top of the action. Photo of scope mounted on rail is there clearance between the front bell of the scope and the rail. This rail needs to be shortened to suit the scope and the action, and your ring placement needs to be further apart. Just a couple of things that may have been missed or need attention. Another thought is your barrel true and straight in the action or its self, it dose not take much of a deviation from straight to stuff every thing up.
-
- Posts: 15
- Joined: Sun Feb 25, 2018 2:03 pm
Re: Nightforce Benchrest 12-42 x 56 running out of elevation
Ok the rifle is back with a 30moa rail on top.
As per the gunsmith there was nothing wrong with the original set up,just that 40moa elevation with a 20moa rail is not enough to reach 800m in a .308 running 155gr HBCs.
At least I can get on with shooting again & working out a load for the new barrel.
As per the gunsmith there was nothing wrong with the original set up,just that 40moa elevation with a 20moa rail is not enough to reach 800m in a .308 running 155gr HBCs.
At least I can get on with shooting again & working out a load for the new barrel.
-
- Posts: 408
- Joined: Sat Feb 08, 2014 6:58 pm
- Location: Barossa Valley
Re: Nightforce Benchrest 12-42 x 56 running out of elevation
I don't think that's right. Your bullets must be traveling very slow if you can't get to 800 metres with a BR and 20MOA rail. If I'm reading what you've said right that means you have 70moa total now?
Return to “Equipment & Technical”
Who is online
Users browsing this forum: No registered users and 65 guests