Lapua 284 brass

BATattack · Post by **BATattack** » Fri Oct 30, 2020 4:51 pm

Maybe I've been under a rock but I didn't know lapua were bringing out straight .284 brass?

https://www.nioa.com.au/products/lapua-unprimed-brass

Shobby · Post by **Shobby** » Fri Oct 30, 2020 5:12 pm

Well It's showing on Nioa's site.

Post by **AlanF** » Fri Oct 30, 2020 5:40 pm

I seem to remember mention of a special order in the US, that wasn't available for export? However if its available in Australia through NIOA then that'll eliminate the need for expanding the 6.5 necks.

PS Maybe it was Norma who did the special order....

Rich4 · Post by **Rich4** » Fri Oct 30, 2020 6:08 pm

And 300 win mag

Wingnut · Post by **Wingnut** » Fri Oct 30, 2020 6:46 pm

I’ve emailed Lapua multiple times asking them to make a straight 284 case. Every time I got a response that they weren’t interested and had no plans to make it. :roll:

cheech · Post by **cheech** » Fri Oct 30, 2020 7:04 pm

Rich4 wrote::D And 300 win mag

Just build a 300 Norma Mag , much more satisfying

BATattack · Post by **BATattack** » Fri Oct 30, 2020 8:12 pm

Maybe they are seeing other boutique makers taking part of their sales and have changed their tune?

I was gonna do a 300 Norma with a SLR treatment a few years ago. Get a nice long neck length to run light and heavy pills with the same throat but blow the body out and the shoulder to something respectable like 35deg.

cheech · Post by **cheech** » Fri Oct 30, 2020 9:01 pm

Well you’re right , I just seen an announcement on FB , 4 new cases for 2021

Redhawk · Post by **Redhawk** » Fri Oct 30, 2020 9:05 pm

https://www.lapua.com/new-lapua-brass-c ... AAny_h1FyU

Rich4 · Post by **Rich4** » Fri Oct 30, 2020 9:09 pm

cheech wrote:
Rich4 wrote::D And 300 win mag

Just build a 300 Norma Mag , much more satisfying

Actually it’s for a 7mm practical, I’ve already got win brass, but been waiting for this

Shobby · Post by **Shobby** » Fri Oct 30, 2020 10:34 pm

I think we are all dreaming for a while.

bruce moulds · Post by **bruce moulds** » Sat Oct 31, 2020 5:47 am

actually necking up 6.5 brass to 7mm is not a bad thing for neck turning if you only have bushing dies.
by using the right sized expander, you can produce internal neck diameters to fit the turner pilot perfectly for the whole neck from the shoulder on out.
bruce.

GSells · Post by **GSells** » Sun Nov 01, 2020 6:50 pm

Hmm probably $5 per case !! Let’s see what they are worth I guess .

Rich4 · Post by **Rich4** » Sun Nov 01, 2020 7:08 pm

Even the magnums are 315 a box, similar to Norma, 284 is only slightly more than 6.5-284, if the turnover ends up the same I’d say the price will too

Rich4 · Post by **Rich4** » Thu Nov 05, 2020 9:48 am

Saum Saum Saum please, pretty please [-o<

At least now they’ve done prc and belted we might see it

Lapua 284 brass

Lapua 284 brass

Re: Lapua 284 brass

Re: Lapua 284 brass

Re: Lapua 284 brass

Re: Lapua 284 brass

Re: Lapua 284 brass

Re: Lapua 284 brass

Re: Lapua 284 brass

Re: Lapua 284 brass

Re: Lapua 284 brass

Re: Lapua 284 brass

Re: Lapua 284 brass

Re: Lapua 284 brass

Re: Lapua 284 brass

Re: Lapua 284 brass