TR - how do you do your load development

If you shoot full-bore, then you're welcome to use this forum to discuss your sport.

Moderator: Mod

SteveG
Posts: 11
Joined: Mon Apr 17, 2023 8:18 pm
Location: Geelong
Has thanked: 3 times
Been thanked: 2 times

TR - how do you do your load development

Post by SteveG »

Relatively new TR shooter here - less than a year.
I've got to the point with my shooting where I think I should do some proper load development so I know that its not my loads holding me back.

My current load is Lapua SRP brass, 46gr AR2208, 155gr Sierra 2156 projectiles. Paramount action with 30" benchmark med palma barrel.
Basically I just chose what I considered a reasonable load based on various sources of info, worked up from a couple of grains lower to confirm there were no issues and stuck with that load as it seemed to be shooting OK.
As a reference - last weekend in good conditions my best strings were a 48.3@700m and a 48.5@800

With a TR rifle how do you handle the sighting aspect for load development? Do you fit a scope or just use the normal aperture sights?
What distance do you do your load development at, and do you shoot off bags or a rest etc?

Steve
Lachlan
Posts: 248
Joined: Mon Sep 21, 2020 12:02 am
Has thanked: 4 times
Been thanked: 38 times

Re: TR - how do you do your load development

Post by Lachlan »

This is from a dirty FO shooter, so disregard my opinion as you see fit, but…

In my brain, the only efficient and effective way to sort loads in a TR rifle, is to do loads like any other F Class/precision rifle. Mount a scope, buy or borrow a really good rest (hopefully your fellow F Class shooters in your club can help you out), fit a front bag rider, borrow or buy a rear bag and shoot your loads at 100. Not fitting a scope to find a load for a TR is insane in my book.
Wakey7
Posts: 149
Joined: Fri Jan 21, 2011 9:18 pm
Has thanked: 55 times
Been thanked: 11 times

Re: TR - how do you do your load development

Post by Wakey7 »

Load development ( in my opinion ) should always be done with the rifle setup as close as possible to how it will be used in competition.
Rich4
Posts: 618
Joined: Sun Feb 24, 2019 2:33 pm
Location: Chinchilla
Has thanked: 2091 times
Been thanked: 255 times

Re: TR - how do you do your load development

Post by Rich4 »

Mount a scope and use a sandbag for extra support, I feel that is the closest to actual use with the most precision.
SteveG
Posts: 11
Joined: Mon Apr 17, 2023 8:18 pm
Location: Geelong
Has thanked: 3 times
Been thanked: 2 times

Re: TR - how do you do your load development

Post by SteveG »

Thanks for the responses. I've shot it with the forestock sitting on a hard rest a couple of times and certainly feels like it behaves differently than when shot with a sling.
Sort of twangy and you really notice the muzzle jump (which is always there just not as obvious with the sling).
So I definitely get the concept of keeping it as close to shooting config as possible when doing load development.

Rich4 - when you say "sandbag for extra support" are meaning to use a front sandbag in addition to normal sling/jacket - or instead of?

Steve
Rich4
Posts: 618
Joined: Sun Feb 24, 2019 2:33 pm
Location: Chinchilla
Has thanked: 2091 times
Been thanked: 255 times

Re: TR - how do you do your load development

Post by Rich4 »

As well as, and not a front rest from f class, different animal, I mean a pile of dirty old cloth bags with a plastic bag inside it to stop the sand leaking out, however many wherever necessary to get the correct support for your prone position to be solid as a rock while allowing recoil tracking consistently, the idea is to remove the wobble but keep the recoil management intact.
The scope may not be necessary depending on your eyesight but it removes doubt for most.
SteveG
Posts: 11
Joined: Mon Apr 17, 2023 8:18 pm
Location: Geelong
Has thanked: 3 times
Been thanked: 2 times

Re: TR - how do you do your load development

Post by SteveG »

Thanks Rich. Makes sense.

Steve
Barossa_222
Posts: 417
Joined: Sat Feb 08, 2014 6:58 pm
Location: Barossa Valley
Has thanked: 188 times
Been thanked: 176 times

Re: TR - how do you do your load development

Post by Barossa_222 »

Don't you just stuff a handful of black powder down the barrel, chuck the ball on top and ram it down with the ramrod?
scott/r
Posts: 895
Joined: Wed Aug 27, 2014 8:22 pm
Location: far north brisbane
Has thanked: 328 times
Been thanked: 161 times

Re: TR - how do you do your load development

Post by scott/r »

Barossa_222 wrote:Don't you just stuff a handful of black powder down the barrel, chuck the ball on top and ram it down with the ramrod?


No. He's asking about tr, not ftr. :D :D
Post Reply Previous topicNext topic