I am looking at using moly coated projectiles and have prepared quite a few using the wet method. The results look really good but not sure where to...
Last post
I have used the dry impact coating with WS2 available from Canada(believe it is the finest micron there is).
I cleaned the barrel vigorously with...
Hello, has anyone modified a caldwell fire control to accept a Seb 3 piece front bag or similar? if so what was required to make it fit.
Last post
About 8 years ago I and my friend in NSW, Peter, each bought one. Soon found the joy stick did not work smoothly.
Took them apart and found very poor...
Just wondering what bipod shooters are doing to improve, solidify and maintain position and technique.
From time to time I wonder if some...
Last post
I only had a short lived attemp with the fclass bipod before going back to joy stick rest.
Free recoil worked for me and found having the bipods feet...
Hi all
Just wondering if anyone has or knows of any stock makers that have patterns of Macmillan a5 or manners t4 stocks that I would be able to get...
Last post
Gday, I have just had a stock put together by Ken Noye in Bacchus Marsh based on an A3 pattern. Ken has quite a few different patterns available and...
I have been shooting F-open for a bit over 2 years now primarily just for fun at my local club and...
Last post
Everyone's jam is different depending on how they determine it and as far as I know Alan has a 284 Shehane and uses Moly so load for a 284 should be...
Hi All,
I'm thinking of building a 260 AI or 243 AI for a bit of fun on a Remington action and I want it to feed from a magazine.
Will I need to use...
Last post
Hi Tim
It really depends on the reamer, and how close to lands you want to be.
Matt
I would like some feedback on GC Inch actions. I have been looking at the action and the fact that they have a rear locking bolt
and thought that may...
Last post
Danny,
I love this fprum and nisit regularily.Always interestng..
Yours
Rpbert Chombart
c-g-designs.blog4ever
A the recent NRAA Queens, I shot a Bartlein barrel that Craig McGowan gave to me for free, to see if I could get it to shoot.
Its original owner had...
Last post
I am a work at the abattoir at the minute, but tomorrow i will get you a couple of "comparative" photos of one of the other...
Ok for a long time I was using cci 400 in my Palma brass. Then I went to cci 450 magnum. Question I have had anyone done a test to see how much of a...
Last post
On accurateshooter some have found some batches of BR4's were hotter than 450's. From memory the rem 7.5 was also shown as producing a larger...
Does anyone know of a gunshop that sells VV powder in Sydney? Also with powder equivalents, if someone used say 20gn of H4198 (USA) and here the adi...
Think it's about time we had a discussion about the quality and expense of some of these scope rails and mounts now on the market. Quite a few are...
Last post
This I can understand, however, by not flexing as much as the action in resistance to it's strength the frequency of vibration would increase perhaps...
Hi all new to this group
I'm planing to build a 7mm saum using 168gn VLDs with ar2213sc or ar2217
On a CZ or Winchester 300-338 win-mag action (if I...
Last post
I have a SAUM built on a savage 12 target repeater action with a magnum boltface, that has won once and placed a few times in F open OPMs , but...
Hi all new to this group
I'm planing to build a 7mm saum using 168gn VLDs with ar2213sc or ar2217
On a CZ or Winchester 300-338 win-mag action (if I...
I am planning a custom build at the moment and would appreciate any opinions related to the GRS KELBLY X-EATER. Are they worth it or should I rather...
Last post
I have the GRS F class stock that was replaced by the X eater.....
What I like about it:
1. The ply is dense and supports the barnard bedding block...
Hi All,
Not sure if this has been covered yet?
I was wondering what peoples experience is with leaving a round in a hot chamber for a while before...
Last post
There is definitely some sort of 'effect'.
How it effects your own rifle can vary very slightly though, so its worth trying your own to find out its...
Hi guys.
I've just got a second barrel to use with my Barnard, & was
wondering whether I should use a tension wrench to torque to a specific...
Last post
For what its worth, Peter Hallet one of our most revered shooters and armouror told me 38 years ago to use 120 ft pound and he did relate a story of...
I read online that from pointing projectiles that people often see improvements in elevation. If this is the case, can the presumption be made that...
Last post
Thanks guys I have all the pointing gear and haven't done the testing with it yet without a home range anymore and the closest one only gong back to...
I'm on a ballistic roll at the moment with whats happening in Australia and overseas and my next project is about to get started, based solely on a...
Last post
I ran them yesterday in competition the misus and I shot a possible hers was 60 with 6 mine was 60 with 4 and second string she shot 59 and I got 58...
Hi all! Does anyone weight sort their primers and have they proven that it improves or halves the Standard Deviation of their loads? And is it worth...
Last post
Ok , I'll come clean ! I've turned into an obsessive compulsive shooter now and have weighed my primers . Testing at 1000 yds even just weighing to...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
Menu
Newest members